Can I use a jointer as a planer? jointer vs planer.
Instead, select a 10- to 12-tpi blade for larger, gradual curves, or a 20-tpi blade for tight curves (1″ radius or less) in solid wood and all cuts in plywood or melamine-coated particleboard. Beyond tooth count, also consider the blade design.
To cut melamine or laminate boards without chipping, your saw must be equipped with a double-sided laminate / melamine blade. These blades are specially designed for cutting and at the same time minimize chipping. Before making your cuts, get your table sawed as best you can.
- Step 1: Measure and Draw your Cut Line.
- Step 2: Place your Tape and Draw the Line Again.
- Step 3: Attach the Guide and Put on your Safety Gear.
- Step 4: Clamp the Board and Start the Saw.
- Step 5: Complete the Cut.
The jigsaw can be used to make both straight and curved cuts in a wide variety of materials, including wood, particleboard, plywood, plastic, metal, even ceramic tile. It’s also safe and easy to use, which is why it’s often the very first power saw a new DIYer buys.
A jigsaw cuts MDF as easily as it cuts plywood, although you should keep in mind that the more teeth the blade has, the less chance there is of chipping the material around the edges of the cut. … You can also cut curves in MDF with a handheld multipurpose or rotary tool fitted with a multi-purpose cutting blade.
Melamine-coated particleboard is a great material for storage, basement, garage, home office, and kid’s room projects. … Unfortunately, the plastic resins in the coating are prone to chip when cut with a spinning saw blade.
Plastic laminate is surprisingly easy to cut. You can do it with a circular saw, a jigsaw, a router or even some hand tools. Cutting a sheet laminate by itself is best done with tin snips or aviation snips, provided you’re cutting it oversize and will trim it later.
The Bosch T101BR jigsaw blade is an ideal choice for cutting laminate materials. The blade cuts on the down stroke, not on the upstroke, the “R” in the product code referring to its “reversed” teeth. This is a popular blade often referred to as a worktop blade.
What is the best tool to cut a laminate worktop? A circular saw is often the best option to cut laminate worktops. Make sure the blade is sharp (replace the blade if you have been using it for a while) and suitable for fine cuts—it should cut through the worktop without any issue.
Speaking of power tools, the Jigsaw reciprocates a straight blade, and a miter saw is a circular saw that can be set to make an angle cut, like making the 45° cuts for a picture frame. The jigsaw basically acts like a free hand scroll saw. Jigsaws work best for cutting softwood that’s no more than 1-1/2 in.
For internal corners, you can cut a 45 deg mitre on one piece, with either a circ saw or mitre saw, then follow the line of the cut on the surface, cutting away the mitred bit with a scrolling blade in a jigsaw (90 deg). This piece will then butt against the other making the “mitre”.
Although a jigsaw can be used for most of the tasks that a circular saw can perform, including straight cuts and cuts on a tilt, the jigsaw uses that really take advantage of the tool’s qualities are jobs such as kitchen fitting and joinery, with their frequent need for complex cuts.
MDF is a highly fibrous material and will quickly dull blades. Always use carbide blades, and use the sharpest blades available. More TPI on your saw blade will result in smoother cuts with less chance of chipping. Lower TPI blades will cut faster.
Cutting It To do this, use a sharp knife (like a utility knife) and drag it along the edge of the straight edge several times to make a shallow cut along the line.
- Engineered wood is easy to damage. One of the main differences between solid and engineered wood is the surface. …
- MDF is heavier. …
- MDF is vulnerable to extreme heat Remember that engineered wood is made out of wax and/or resin-like compounds. …
- MDF can’t support too much weight.
A hand-held jigsaw makes intricate cuts relatively simple. The blade of a jigsaw cuts on a downward motion, so make cuts on the face side of the paneling to reduce splintering.
To make straight cuts in your MDF, acquire a circular saw that has a cutting speed between 3,000 and 3,350 metres per second (9,800 and 11,000 ft/s). For the best cut possible, install a blade that has at least 60 teeth and a width of about 355 mm (14.0 in). For additional strength, pick a blade that has a carbide tip.
cut laminate properly for smooth edge A common problem with cutting laminate is a rough, chipped edge, which is usually caused by a dull saw blade or the use of a saber saw. Using a sharp, carbide-tipped blade (preferably on a table saw) is the best bet for a smooth edge.
Melamine is difficult to cleanly cut with most DIY tools, giving at best, one clean face, and one chipped side. Using a jigsaw will potentially damage both faces due to the sawing motion of the jigsaw. If you intend to cut melamine, we recommend using a circular saw.
Since melamine is a plastic resin, it’s prone to chip and splinter. Luckily, there are a few easy tricks to get perfectly clean, factory-like edges. … Second, set your table saw or circular saw blade to cut about 1/4″ into one surface of the melamine.
Melamine: Melamine is more economical and easier to look after for the kitchen and bathroom cabinet boxes and shelves. … MDF is a dense fiberboard and very heavy, in fact, too heavy for cabinet boxes. MDF doors cost as much as Maple framed doors and they are heavier than Maple doors.
To cut through laminate countertops, you can use a hand saw, but a circular saw makes the job much quicker. Because a circular saw can produce jagged edges and chip the laminate, your best bet is to lay the laminate face-side down and cut from the back to the front.
Turn the laminate counter upside down so that the finished side is facing downward. Use a tape measure to determine where you need to cut it and draw a line at the location with a pencil. Put on safety glasses and plug in a jigsaw. Turn the jigsaw on and move the blade along the pencil line to cut through the counter.
Diamond-tipped blades that are made for laminate and fiber cement usually have a low number of teeth to reduce the dust produced by cutting cement. However, typical circular and miter saw blades that are used for laminate will have 80 to 100 teeth for fine, precision cutting.
For solid and veneered worktops, you need a cross-cut, fine tooth saw blade with 48 teeth. For laminated worktops, it is advisable to use the triple chip grind saw blade, also with 48 teeth.
it is best to use a circular saw for cutting work tops to length, and if so work from the bottom of the worktop, NEVER from the top, as the teeth on a circ blade cut UPWARDS…..and also cut from the front bullnose or what ever face shape, as if you start from the back you risk breakout from the front…but never use a …
You don’t need to turn the worktop upside down before cutting it. If the worktops are a dark color although sometimes I will do this anyway, place a strip of masking tape on the worktop where you need to mark it. This will make the pencil lines much more visible.
Jigsaws are the only portable power tool that can effectively cut curves. This makes them a must-have for any woodworker who wants to get the job done faster than with a hand-held coping saw. … This adds to the tool’s versatility and makes it more valuable in your workshop.
With their long, slim blades, jig saws are ideal for jobs that require delicate wood cuts. … Reciprocating saws, however, with their horizontal blade action, are designed primarily for rough cutting and demolition jobs, such as cutting wood and metal aggressively.
The table saw, in my opinion, is the most versatile tool in the shop and should be your first major purchase. Next up is the Miter Saw. The miter saw does one thing but it does it really well. The Miter saw will cross cut wood better and faster than pretty much any other tool.