How do I tighten the chain on my Echo chainsaw?

Chain Not Set Properly One of the most common reasons why your chain might be coming loose is because it was not set properly. When you go through the steps to tension your chain, you need to finish those steps by setting the tension so it won’t change as you work your saw.

The chainsaw chain should feel snug but still pull freely. Finally, perform a “snap” test to ensure proper saw chain tension. Simply pull the chain on the underside of the guide bar down so one or two drive links are out of the guide bar rails and release it. The chain should snap directly into position.

There is a tension screw located near the base of the bar on the chainsaw. To tighten the chain, turn it clockwise, and to loosen turn it counterclockwise. Don’t over-tighten the chain as this could cause it to break.

Good Tension- A properly-tensioned chainsaw chain should still be just a little loose on the chainsaw guide bar, but the chain needs to be tight enough that you can’t pull the drive links out of the bar nose.

The chain should be tight enough that it only allows you to move it up and down about half an inch. If there is no slack in the chain then it is too tight. And if there is too much slack then you need to tighten that chain.

Every chainsaw has a tension screw that’s located at or close to the base of the chainsaw bar. If you want to tighten the chain, turn the tension screw clockwise. If you want to loosen up the chain, turn the tension chain counterclockwise.

To tighten the chain on a fixed-gear bike, start by flipping the bike over or placing it on a bike stand. Loosen the rear axle and then pull back on the rear tire to make the chain tighter. Make sure the chain isn’t too tight or too loose, then tighten the rear tire again.

To adjust chain tension, loosen the bolts that fasten the motor base to mounting angles on both sides. Tighten take-up bolts until desired chain tension is reached. Do not over-tighten. A good rule of thumb is 1/4″ deflection in the chain between the sprockets.

The most common cause of a chainsaw that won’t cut properly is a dull cutting chain. Try sharpening or replacing the chain. The chain may not have the proper amount of tension. … If the chain is too tight, the chain may not rotate at the proper speed, causing the chain not to cut properly.

Loosen the guide bar nuts and turn the adjusting screw counter-clockwise 1/4 turn to loosen the chain if it is too tight. Loosen the guide bar nuts and turn the adjusting screw clockwise 1/4 turn to tighten the chain if it is loose. Tighten the guide bar nuts firmly with the guide bar adjusting wrench or socket wrench.

Its elongation is caused when material is removed from the pins and bushings. The individual joints in a roller chain articulate as they enter and leave the sprockets. … This articulation results in wear on the pins and bushings. As material is worn away from these surfaces, the chain will gradually elongate.

When you own a chainsaw and see that it does not cut as well anymore you will have to decide whether to replace it or sharpen the chain. A chainsaw chain could serve you for more than five years if it is occasionally used, and still help you accomplish most of your tasks.

Common solutions for: Echo Chainsaw not cutting The most common cause of a chainsaw that won’t cut properly is a dull cutting chain. Try sharpening or replacing the chain. The chain may not have the proper amount of tension. If the adjustment screw is too loose, the chain may not make good contact with the wood.

This most commonly is a result of a dull chain and exerting to much pressure on the bar and chain trying to make the chain saw cut. This could also be either a lack of bar and chain oil ( tank empty, restricted oiler hole ) or an inferior type of oil that is being slung off the chain and not lubricating.

Stringy wood can do this. Too low of rakers will allow the cutters to take too big a bite and it can stop the chain or cause it to chatter in the cut. Seeing it’s a new saw with a new chain I doubt it’s your rakers. Probably a combination of stringy wood and a saw that’s still getting broken in.